Finger Pinch Loosening and Tightening Torques on Small Cylindrical Handles Among Industrial Workers
DOI:
https://doi.org/10.37266/ISER.2013v1i2.pp144-152Abstract
An experiment was conducted with 23 assembly line workers in a manufacturing plant to study to the variation in finger torque strengths on small handles. Subjects exerted MVC torques on small cylindrical handles with different finger contact surface finishes (smooth and knurled) and different diameters (3.3, 5.0, 6.4, 9.5, and 19.0 mm). Three similar handles with flanged finger contact were also tested to simulate torqueing on a specific medical device. The flange widths were 6.4, 9.5, and 19.0 cm. Both loosening and tightening peak torques were measured. Ten males and 13 females between the ages of 22 and 55 years were tested. Each performed 26 different torque exertions while standing (20 on cylinders and 6 on flanges). The results indicated that finger torque strength decreased steadily as diameter of the cylindrical handle, or length of the flange, decreased. It was also stronger for tightening compared to loosening, and for knurled cylinders compared with smooth cylinders. Of greater interest was the 2-factor interaction effects on torque – surface*direction, surface*diameter and diameter*direction for the cylinders; and direction*width for the flanges. These interactions indicate that the change in torque over one torqueing factor is not independent of other factors. These results have implications for the design of small device parts, as in some types of medical products.
References
Adams, S.K. and Peterson, P.J. (1988). Maximum Voluntary Handgrip Torque for Circular Electrical Connectors. Human Factors, 30(6): 733-745.
Habes, D., Grant, K. (1997). An electromyographic study of maximum torques and upper extremity muscle activity in simulated screwdriving tasks. International Journal of Industrial Ergonomics 20, 339–346.
Imrhan, S. N. and Farahmand, K. (1999). Male Torque Strength in Oil Rig Tasks: The Effects of Grease Smeared Gloves and handle length, diameter and orientation. Applied Ergonomics, 30(5): 455-463.
Imrhan, S. N. and Jenkins, G.D. (1999). Flexion-Extension Hand Torques – Applications in Maintenance Tasks. International Journal of Industrial Ergonomics, 23: 359-371.
Imrhan, S.N. and Loo, C.H. (1988). Modeling Wrist-Twisting Strength of the Elderly. Ergonomics, 31(2): 1807-1819.
Imrhan, S.N., Brown, M.J. and Mandahawi, N. (2005). Finger pinch torques on small handles. Proceedings of the XIX Annual International Ergonomics and Safety Conference, 2005, Las Vegas Nevada, CD-ROM, Lockhart, T. and Fernandez, J.E. (eds.), pp. 172-175.
Kroemer, K.H.E, Kroemer, H.B. and Kroemer-Elbert, K.E. (1994). Ergonomics: How to design for ease and efficiency, Prentice Hall, Englewood-Cliffs, NJ.
Pheasant, S., 1986. Bodyspace: Anthropometry, Ergonomics and Design. Taylor and Francis, Philadelphia, PA.
Shih, Y., Wang, M., 1996. Hand/tool interface effects on human torque capacity. International Journal of Industrial Ergonomics 18, 205–213.
Rohles, F. H., Moldrup, K. L. and Laviana, J. E. (1983). Opening Jars: An Anthropometric Study of the Wrist-Twisting Strength of Children and the Elderly. Report no. 83-03, Institute for Environmental Research, Kansas State University.
Swain, A.D., Shelton, G.C., and Rigby, L.V. (1970). Maximum Torque for Small Knobs Operated With and Without Gloves. Ergonomics, 13(2): 201-208.
Published
How to Cite
Issue
Section
Authors who publish with this journal agree to the following terms:
- Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
- Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.
- Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work (See The Effect of Open Access).
The copyediting stage is intended to improve the flow, clarity, grammar, wording, and formatting of the article. It represents the last chance for the author to make any substantial changes to the text because the next stage is restricted to typos and formatting corrections. The file to be copyedited is in Word or .rtf format and therefore can easily be edited as a word processing document. The set of instructions displayed here proposes two approaches to copyediting. One is based on Microsoft Word's Track Changes feature and requires that the copy editor, editor, and author have access to this program. A second system, which is software independent, has been borrowed, with permission, from the Harvard Educational Review. The journal editor is in a position to modify these instructions, so suggestions can be made to improve the process for this journal.
